Photo of Aluminum Classic II service body courtesy of The Reading Group.

Photo of Aluminum Classic II service body courtesy of The Reading Group.

A growing trend in second-stage manufacturing is light-weighting, which involves specifying lighter-weight materials to achieve an overall weight reduction to an upfitted vehicle. The increased use of lightweight materials in upfit packages has been on the rise for several years and there are many advantages to doing so.

First, specifying lighter-weight upfit materials decreases the vehicle’s curb weight, which, in turn, lowers operating costs by reducing fuel consumption. In addition, by reducing fuel consumption, fewer greenhouse gases are emitted, which contributes to meeting corporate green fleet goals. Similarly, many lightweight materials used in upfits are recyclable, further contributing to a corporation’s overall sustainability initiatives.

A second benefit to reducing GVW is that it creates the potential opportunity to downsize to a smaller vehicle. In certain situations, the lightweight upfit may enable the fleet to select a smaller chassis that not only improves fuel economy, but also lowers initial acquisition cost. A corollary benefit to lightweighting is the ability to increase the legal payload of the vehicle without having to migrate to a larger truck. The decreased weight from lighter service bodies, racks, bins, and shelves is reciprocally converted into increased payload, allowing fleets to carry more cargo and accomplish more with the same vehicles. Similarly, the additional capacity may result in fewer trips per day because the vehicle can carry more payload. It is important to note, that while lightweighting may allow a fleet to increase payload or reduce fuel consumption, it cannot achieve both simultaneously.

A lightweighting strategy is designed to take weight out of the vehicle by specifying upfit components built from lightweight materials, such as aluminum, fiber-reinforced composites (FRC), or fiber-reinforced plastic (FRP) composites. Similarly, today’s cargo van interiors feature increased use of lightweight materials to reduce overall vehicle weight. Upfitters are transitioning from steel racks and bins to heavy-duty plastic composites and aluminum. Lightweighting also extends to auxiliary equipment mounted on a service body, such as aerial platforms and other equipment, that use high-strength steel, which is thinner and lighter than traditional steel, but with comparable strength. "The point of using high-strength steel is to use less material by having thinner walls," said Andrew Halonen, president of Mayflower Consulting. "The same aerial boom made of high-strength steel is lighter than the thick-wall version made of a lower strength steel. Over the past five decades, the use of steel in the automotive market has stayed largely the same, about 75 percent of the vehicle; yet, as the stronger grades became available, the sheet metal got thinner.”

Corrosion resistance is another benefit of some lightweight materials, specifically aluminum, fiberglass, and plastics, which helps extend the service life of an upfit, especially those operating in Snowbelt states and coastal regions.

Steel is the material of choice for the understructure of a service body, especially in utility applications, because of the twist and torque of the body when a truck travels off-road or is mounted with a crane or aerial device. However, there are opportunities for lightweighting a service body at nonstructural areas in the body, such as side compartments, doors, floor pan, aluminum tool boxes, ladder racks, and other service-body-mounted equipment.

Many truck fleet managers recommend a “blended approach” to lightweight material and steel selection to provide a balance between weight savings, strength, durability, and cost. Conventional steel continues to be the predominant material used in service bodies because of its relative low cost and its durability under severe work conditions.

Lightweight materials aren’t appropriate for every application. Lighter-weight materials, in many cases, have a lower strength compared to steel. Also, lightweight materials, for the most part, have a higher initial cost relative to conventional steel, depending on the type of material and amount of that material used in the upfit design. While lightweight materials may increase fuel economy, will the vehicle travel a sufficient number of miles per year to recoup the higher materials price? In a low-mileage duty cycle, the total cost of ownership (TCO) of steel may pencil out better because the vehicle won’t be driven enough to justify the higher materials cost. Some lightweight materials do not have the same durability as steel, which are required for extended lifecycles or severe-duty applications.

When used in the manufacture of truck bodies and van equipment, lightweight materials, such as thinner gauge high-strength steel, aluminum, fiberglass, and plastic composites, enable fleets to reduce vehicle weight to improve fuel economy, increase legal payload, and even drop down to a smaller (often more fuel-efficient) vehicle.

However, the fundamental consideration is to validate whether the lightweighted equipment and materials will be able to fulfill the intended fleet application. Lightweighting involves complex decision-making and is much more than simply decreasing weight.

Let me know what you think.

[email protected]

About the author
Mike Antich

Mike Antich

Former Editor and Associate Publisher

Mike Antich covered fleet management and remarketing for more than 20 years and was inducted into the Fleet Hall of Fame in 2010 and the Global Fleet of Hal in 2022. He also won the Industry Icon Award, presented jointly by the IARA and NAAA industry associations.

View Bio
0 Comments